BMW ICOM NEXT | BMW NBT EVO FSC Codes | BMW NBT & CIC FSC Codes | BMW Rheingold , ISTA/P, KSD, ETK remote installation | BMW STANDARD TOOLS remote installation | BMW ESYS remote installation
Go Back   BMW forum. Diagnostics, coding, programming, repair BMW vehicles. > BMWelcome > BMW diagnostics and repair

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 11-16-2013, 06:48 AM
Junior Member
 
Join Date: Oct 2013
Location: miami
Car: 2009 550i
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
Default BST/airbag error even with 2.2 ohm reading

I have a 2009 550 that was in a accident, the bst was replaced along with the 4 airbags that was fired. Im getting a good reading from the bst of 2.2ohm if I put a ohm meter on the wires, also the passenger head airbag is also read 0 ohm in autologic and inpa but they both give proper value if I hookup a ohm meter. The passenger head airbag was not triggered during the accident, I even bought another know good airbag and tested and they both give the same ohm reading when using a ohm meter. Also the acsm complained about the 3crash fault 93d5. could the 3crash fault cause the airbags and bst to register proper value?


Reply With Quote
  #2  
Old 11-17-2013, 05:09 PM
Member
 
Join Date: Jan 2013
Location: CA
Car: 03 x5,06 530xit,87 325is race car
Posts: 31
Thanks: 7
Thanked 3 Times in 3 Posts
Default

I had a similar problem with a 10 535i.All airbags and BST were replaced and the unit was still reading short in the BST.I tried reprogramming,but there were faults in the TCU communication and the programming was impossible with ISTA.I found airbag module from a similar car(with deployed airbags) and it worked out flawlessly after resetting.
So probably you can try reprogramming with INPA,ISTA or Progman.
Reply With Quote
  #3  
Old 12-07-2013, 02:45 AM
Junior Member
 
Join Date: Oct 2013
Location: miami
Car: 2009 550i
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by bawareca View Post
I had a similar problem with a 10 535i.All airbags and BST were replaced and the unit was still reading short in the BST.I tried reprogramming,but there were faults in the TCU communication and the programming was impossible with ISTA.I found airbag module from a similar car(with deployed airbags) and it worked out flawlessly after resetting.
So probably you can try reprogramming with INPA,ISTA or Progman.
ok I had the airbag module reset but same error, I'm going to buy another acsm and see if that help. thanks for replying
Reply With Quote
  #4  
Old 12-08-2013, 09:27 PM
Junior Member
 
Join Date: Jun 2013
Location: Macedonia
Car: 2002
Posts: 12
Thanks: 0
Thanked 0 Times in 0 Posts
Default

3 crash telegrams stored

means you have to reprogram the ACSM or replace
Reply With Quote
  #5  
Old 12-31-2013, 06:21 AM
Member
 
Join Date: Jan 2013
Location: CA
Car: 03 x5,06 530xit,87 325is race car
Posts: 31
Thanks: 7
Thanked 3 Times in 3 Posts
Default

Quote:
Originally Posted by dimitar View Post
3 crash telegrams stored

means you have to reprogram the ACSM or replace
I have talk to a few friends across the ocean and no one believes me.Here in the US BMW SRS modules can be reset,no matter of the severity of the accident.My X5 had all airbags,belts and SBT deployed and it reset just fine after everything was replaced.And it was done on many other bimers with 99.9% rate of success.
Reply With Quote
  #6  
Old 01-08-2014, 07:37 AM
Junior Member
 
Join Date: Jan 2014
Location: USA
Car: i20
Posts: 7
Thanks: 0
Thanked 1 Time in 1 Post
Default

I don't face any problems like these because i regularly checkup my car form BMW service center and they programed it manage it with good care so i say if you can't able to programed it then go your car service center they re-programed your car.
Reply With Quote
  #7  
Old 03-04-2016, 08:52 PM
Junior Member
 
Join Date: Jan 2016
Location: Romania
Car: bmw 320d
Posts: 3
Thanks: 0
Thanked 1 Time in 1 Post
Default

Hello. I have same issue with acsm2 on e70. I know it can be reset with tool32 but do not remember the procedure. I do bme coding for some years... have all hardware needed . If someone knows the procedure please share it. I appreciate any help. Thanks
Reply With Quote
The Following User Says Thank You to foreverbmw For This Useful Post:
nanotech (01-04-2017)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
R53 Airbag Error mr_bean BMW diagnostics and repair 1 05-23-2013 03:24 AM
NCS-Reading VO(FA) and INPA-Engine(DME) read error tinkerman BMW coding and programming 3 04-11-2013 05:26 AM
airbag error message on a e85 z4 chrisj900 BMW GT1, OPS/OPPS, INPA 3 12-25-2011 09:45 AM
INPA Reading/ Coding E38 1995 with ODB1 20 pins, get error ingar@spn.no BMW diagnostics and repair 1 12-07-2011 04:35 PM
Error with INPA Reading/ Coding E38 1995 ODB1 20 pin ingar@spn.no BMW GT1, OPS/OPPS, INPA 0 12-01-2011 09:44 AM


All times are GMT. The time now is 12:14 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.1
BMW forum: diagnostics, coding, programming.