BMW ICOM NEXT | BMW NBT EVO FSC Codes | BMW NBT & CIC FSC Codes | BMW Rheingold , ISTA/P, KSD, ETK remote installation | BMW STANDARD TOOLS remote installation | BMW ESYS remote installation
Go Back   BMW forum. Diagnostics, coding, programming, repair BMW vehicles. > BMWelcome > BMW diagnostics and repair

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 11-30-2011, 07:05 AM
Junior Member
 
Join Date: Nov 2011
Location: Norway
Car: Bmw 730 1995, Bmw Csi 2.8 1969
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Default INPA Reading/ Coding E38 1995 with ODB1 20 pins, get error

Hi!:) I have installed Inpa 5.02, Eidiabas, Nc expert + the tools.
used this option when I installed "BMW Group Rectification programs UK"

I have a Bmw from Januar 1995 E38 730i M60 engine.
with the first LCM module(I think it s bad because full beam don'nt work)

Use USB ODBII cable + ODBII to 20 pin ODBI Converter cable.

I use shift + F9 to change to old Bmw models and choose body LCM, IKE
But when I try to read LCM and IKE I get "could not communicate with unit"
and script errors.

I can read automatic gearbox + some more modules.

I know that there is new LCMII module in 9/1995, mybee the program try to read
the never LCM and IKE module.

Does anybody know how I setup Inpa , Eidiabas to support all modules in my 2/95 E38?
Or is there some configuration files I can download?

PS. "I think LCM is bad because full beam don'nt work, but if I use the light horn full beam
comes on, but it is impossible to turn it of, it turns of if I press the light horn fast in and out.
I tried to change LCM but i was the same, somebody who know what can be wrong?
I happends when I mounted trailer module/tow bar and did a wrong wire connection"

Regards Ingar Granholt
From Norway
Homepage [Only for registered users... ]


Reply With Quote
  #2  
Old 12-07-2011, 04:35 PM
Junior Member
 
Join Date: Nov 2011
Location: denver
Car: '92 525i
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Default

hi,
i have not coded anything to that particular model or year range, but i do know that early models with the factory 20-pin connector have limited communication to control units through the obd-II port. I would try and use the 20-pin and see if you are able to communicate to the control unit, if you are still unable to communicate with the 20-pin there is an issue with the system that will have to be rectified before programming.
good luck :)
Reply With Quote
Reply

Tags
beam, e38, inpa, lcm

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
NCS Error iph-0006 EDIABAS or SGBD Error thisizaremix BMW GT1, OPS/OPPS, INPA 5 06-09-2014 07:26 PM
Job Status Error [Error ECU Rejected] instead of [Okay] when trying to clear SRS ligh cboy BMW GT1, OPS/OPPS, INPA 2 04-21-2012 08:43 PM
Error with INPA Reading/ Coding E38 1995 ODB1 20 pin ingar@spn.no BMW GT1, OPS/OPPS, INPA 0 12-01-2011 09:44 AM
INPA error weiss BMW GT1, OPS/OPPS, INPA 5 08-21-2011 07:39 PM


All times are GMT. The time now is 06:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.1
BMW forum: diagnostics, coding, programming.