BMW forum. Diagnostics, coding, programming, repair BMW vehicles.

BMW forum. Diagnostics, coding, programming, repair BMW vehicles. (http://bmwcoders.com/forum/)
-   BMW GT1, OPS/OPPS, INPA (http://bmwcoders.com/forum/bmw-gt1-ops-opps-inpa-24/)
-   -   IFH-0009 cannot connect (http://bmwcoders.com/forum/bmw-gt1-ops-opps-inpa-24/ifh-0009-cannot-connect-198/)

AlexK 05-16-2011 09:40 PM

IFH-0009 cannot connect
 
Hi everyone,

I am new here and have just purchased a EDIABAS OBD2 connector with INPA v5 software. I receive an error ifh-0009 when connecting to the vehicle. I am using an IBM laptop running windows xp and connect via a usb serial parallel adaptor. I diable the com 1 and set the serial to com 1.

Please help.

Regards,
Alex K.

Admin 05-17-2011 08:04 AM

IFH-0009: ECU isn’t connected or doesn’t respond

Reason 1: In the Ediabas.ini file, the interface is set to STD:ADS. However, you have
connected an OBD connector.
Solution 1: Modify the interface setting.
Reason 2: The ignition is switched off.
Solution 2: Switch the ignition on.
Reason 3: The device manager has been used to disable the FIFO buffer for COM1.
Solution 3: In the device manager (Windows XP: Enter “Start” “Control Panel”
“System” “Hardware” “Device Manager” Ports (COM & LPT)), and select
COM1 from the ports and under the “Port Settings” tab, select “Advanced”. There
must be a check-mark by “Use FIFO buffers” and the highest possible setting
must be selected for the receive buffer.

boki01 06-26-2011 03:08 PM

I already try everything and check settings couple of times, but still geting error messages IFH-0009 & SYS-0012, running on windows XP, USB to OBD II cable INPA compactible...Any solutions?

Admin 06-27-2011 07:19 AM

Quote:

Originally Posted by boki01 (Post 965)
I already try everything and check settings couple of times, but still geting error messages IFH-0009 & SYS-0012, running on windows XP, USB to OBD II cable INPA compactible...Any solutions?

What car? What cable?

mcdesire 02-07-2012 02:39 PM

Same Problem
 
Hi guys im having the same problem, Bought the kit from [Only registered and activated users can see links. Click Here To Register...]

Same error, Shows the engine and battery light in black but when i try to sync the EWS DME it comes up with same error.

Any other ideas have checked everything else.

TxT 02-29-2012 05:35 PM

Hi,
Perhaps is a stupid check but, Did you turn off the windows firewall and antivirus?.
when I installed the software I got the same error.
I repeated all the installation steps after turning off the firewall and antivirus and finally it works.
Did you executed the API-Test?

ebbano 03-18-2012 11:09 PM

Thank I've had same poroblem.

540is 07-01-2012 12:06 PM

I have this problem when trying to connect to Engine, Steering sensor, and ABS/EWS
the other functions like ie. airbag works fine.

E39 / S62, tried two diffrent cables with same problem.

Tried the solutions in this post, still same issue, using XP & inpa 5.0 (tried in win7 - same issues)

Any ideas on troubleshooting?

540is 07-02-2012 08:02 AM

What differs that interface from ie. this one:

[Only registered and activated users can see links. Click Here To Register...]
that I'am using right now - configured as K-Interface.

peatun 09-10-2012 03:51 PM

I had the same issue but found that my cable (said it was INPAS style) didn't have pin 7&8 linked so I had to solder in a jumper.


All times are GMT. The time now is 03:03 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.1
BMW forum: diagnostics, coding, programming.